Laboratory furnace

Introduction to laboratory furnace
The quality aluminum silicate fiber, state-of-the-art vacuum molding process and automatic control technology to develop a set of energy-saving, efficient, beautiful and one of the new laboratory furnace. Department of laboratory furnace cycle mode of operation energy-efficient furnace, heating up fast, make no use of small, good temperature uniformity, for laboratory, industrial and mining enterprises for the metallic elemental analysis and general metal heat treatment.
Laboratory vacuum features
1, silicon carbide lining, all-fiber insulation.
 2, laboratory furnace hearth material made of ceramic fiber, thermal capacity is small, fast heating (30 minutes to reach the set temperature), short cycle, saving energy (energy-saving effect is plain old furnace 80? Above).
 3, the use of intelligent digital programmable temperature controller, the preparation of multi-liter, security, cooling curve, automatic heating, insulation, cooling and over-temperature protection, the end of the program to run automatically stop without duty.
 4, high temperature resistance wire heating element placed in the furnace wall heating plate, easy to use, safe Shallow.
 5, can be configured programmable temperature control and other RS485 interface can be configured, remote control and data acquisition laboratory electric furnace. Or configuration circle diagram to adjust the recorder track record of the heat treatment process.

Box furnace (muffle furnace) Precautions

Because box furnace (muffle furnace) products are high fever, so in daily use must pay attention to the safety of life and property of the State Security.
One would be automatic temperature controller flat on a smooth place'' not'' in order to avoid too close from EAF furnace heat affect electronic components'''' and then remove the short route to the furnace with the power cord into an electric furnace and then'' to the power cord connected to AC 220V'' and furnace controllers are effective electrical connection.
Two. Thermocouple with a wire connected to a temperature controller'' Note'' ± pole can not be wrong check again whether there is installed an error.
Three would be the thermostat to the desired temperature'' connected control box "type" of power'''' At this point turn the power switch into the red light green light to start work.
Four when the muffle furnace first time or long-term disabled again after use and must be oven dried.
Note:
Installation of all electrical distribution equipment and instrumentation through checks and adjustments'' and check the furnace and the voltage is normal'''' has good contact with the maximum temperature never exceeds the limit temperature series product configuration object'' to take the furnace must be cut off power to ensure safety'' furnace should be placed in a dry place to prevent moisture'' use'' leakage and cracking caused by heating refractories such as automatic temperature controller needs to swap places'' need'' to connect the console to avoid damage to the short route vibration meter.

Trolley type gas roaster

Trolley type gas roaster advantages:
Trolley type gas roaster pumping gas the hearth the trolley flame furnace, to imported industrial furnace equipment features, by our factory according to China's national conditions and usage, performance and technology to further improve the success of research and development, has now been dozens of home users successfully used for many years, the Practice has proved that this technology is very mature, according to user feedback, it shows significant power savings, temperature uniformity, environmental cleanup, easy maintenance, etc. Compared with the original conventional furnace. The car-type flame gas roaster eruption heat up down the middle of the flue rotation in the case of the top of the arc discharge design, effective control of the temperature uniformity and heat utilization. The furnace by the furnace (including lining) door, furnace vehicles, combustion systems, exhaust systems, sealed, temperature control and records and other major components.
Trolley type gas roaster structural features:
1, trolley type gas a roaster furnace body skeleton by a variety of large and medium-sized steel-site combination welded the shell closure plate color plate overall rugged beauty.
2, trolley type furnace lining the mullite refractory fiber insulation, about 60% of energy relative brick hearth.
3, trolleys skeleton by the combination of a variety of large I-beam, channel steel, angle steel and thick steel plate welded together. Trolley drive motor, worm gear reducer combination through the chain-driven front-end capstan drive. Trolley the refractory masonry the high alumina stereotypes brick structure, the furnace sealing effect, high compressive strength. Trolley and the furnace is sealed with a soft touch, and the lower part of the trolley a labyrinth sand seal groove and sand seal knife sealing device.
3, car type gas roaster oven door with side opening, simple and convenient, sealed with hand wheel clamping mechanism.
4, the combustion system: the installation on both sides of the car-type gas roaster dozens of small burner, multi-burner small heat flow in the furnace cycle back and forth to ensure temperature uniformity. Burning Tsui automatic ignition, instrument control.
, Smoke devices: upper end of the furnace exhaust device, the installation of an adjustable valve plate, the valve can adjust the pressure in the furnace.
6, the control system uses a simple and practical chain control, digital table shows the temperature and contactor control.

Industrial furnace repairs

Industrial furnace repair machinery thermal processing plants mostly in the 650 ℃ -1700 ℃ of temperature, therefore, bear masonry industrial furnaces and furnace heat ablation sudden change of temperature effect.
Of furnace gas and molten slag chemical attack and a variety of materials, high-temperature air and the molten metal impact wear, a combination of factors which accelerate the industrial furnace damage. Therefore, compared with the general cold equipment, industrial furnace technical condition prone to change, life is short, repair more times.
In general machinery plant, the number of industrial furnaces, while small, accounting for the total number of devices 5% -8%, but the annual overhaul Number of units Number of units accounted for all the equipment overhaul 16% -20%.
As we all know, cast iron with a cupola furnace will be carried out for each open one day a small repair; forging furnace, then at least once a year to overhaul.
Industrial furnace repair so many times, fast changes in working conditions at the plant in addition to the individual foundry equipment (such as molding machine, shot blasting machine, etc.), the fear in the number of all types of equipment to be "among the best."

Low-temperature box furnace

Introduction to the low-temperature box furnace
Uses: mainly used steel workpiece quenching, normalizing, annealing conventional heat treatment with special equipment.
Features:
1. Electric furnace loading capacity, high productivity, especially for small and medium-sized mechanical heat treatment heating, energy saving up to 20%, temperature uniformity, the DRO automatically furnace temperature control, high precision;
2. Electric furnace installed Imperial material, operating conditions;
3. The seal of the door and the furnace for self-sealing, without manual sealing
4. The electric furnace has interlock protection device to prevent misoperation due to failures and accidents;

Vacuum atmosphere box furnace

Vacuum atmosphere box furnace uses:
Vacuum atmosphere box furnace according to customer needs all kinds of furnaces, universities, research institutes, industrial and mining enterprises to meet the high temperature sintering, metal annealing atmosphere reduction and quality testing is widely used in materials, physics, chemistry, metallurgy, chemical industry, new energy development and other fields.Vacuum atmosphere box furnace hearth Imported insulation material - high purity polycrystalline alumina fiber, the use of B-type double platinum and rhodium thermocouple temperature and AL artificial intelligence regulator 708P temperature controller automatic temperature control, using artificial intelligence AL adjustment algorithm, no overshoot, industrial-grade single-chip microprocessor, four and a half A / D conversion and digital correction, filtering technology to ensure measurement accuracy of up to 0.2 (± 1 ° C). Furnace shell with double ventilation design, so that the furnace can be rapidly cooling the door using circulating water to ensure that the door is not deformed in the first heat quenched, thereby ensuring air tightness of the furnace, the furnace can work in a multi-atmosphere, improve its scope of use. S of the epoxy-based resin paint made from galvanized stainless steel inside and outside the box, the outer coating of high hardness, attractive appearance, practical.
Vacuum atmosphere furnace features:
1, the control precision: ± 1 ° C furnace temperature uniformity: ± 1 ° C (depending on the size of the heating chamber may be).
2, microcomputer control, easy to operate, programmable, automatic heating, automatic insulation, automatic cooling.
3, fast heating (heating rate of 20-40 ° C / min adjustable).
4, energy (furnace imported fiber made of high temperature resistance, rapid thermal quench).
Furnace fine spray corrosion-resistant acid, furnace, furnace isolation with air-cooled furnace wall temperature close to room temperature.
6, double-circuit protection (over-temperature, over-pressure, superfluidity, paragraph even, power outages, etc.).
7, furnace materials imported refractories, good insulation properties, high temperature resistance, rapid cooling and rapid heat.

Chamber furnace Products

Chamber furnace with a cube or rectangular furnace industrial furnace, also known as box-type furnace. Chamber furnace compartment flame furnace chamber furnace two categories, chamber furnace to strictly control the temperature. Chamber furnace combustion devices or electric components are mounted on the side walls or the bottom of the furnace, heat radiation, convection, and conduction heat transfer of the workpiece. The workpiece is heated to load and remove from the oven door. Furnace chamber structure is relatively simple, for heating of the workpiece in a single piece, small quantities, the workpiece by weight is generally not more than 3 tons, the the hearth area not greater than 10 square meters, the thermal efficiency is low.
Chamber furnace classified:
Chamber furnace uses can be divided into three kinds. The ① chamber furnace: for metal forging and thousands of welding heating furnace working temperature of 1000 to 1300 ° C. Gas and combustion air in the mouth after the first introduction of the burner mixing, then ejected combustion. Combustion gases in the furnace after the heating of the workpiece into the flue, and finally by the chimney into the atmosphere. Stove burner, furnace, metal hob, door, flue and adjust the flue of the furnace pressure gate. ②-chamber-type heat treatment furnace: normalizing, annealing and quenching, the furnace temperature of 800 to 1100 ° C, heating for tempering and aging, the furnace temperature 150 to 700 ° C is used to eliminate stress in the metal forging and heat treatment heating as . (3) Room type roaster: Investment Casting Shell roasting and enamel roasting furnace temperature of 850 to 1200 ° C.
Chamber furnace features:
Chamber furnace with sealed metal furnace shell, the heating element is mounted on the inner surface of the both sides of the furnace, the furnace bottom, and front and rear door. Tightness of the furnace, and more uniform heating, and the furnace temperature can be precisely controlled.